SS-30 Product Description
Download PDF
SS-30 is a fast curing silicone RTV adhesive rubber developed for automotive
gasketing applications requiring fast development of physical properties and
fast unprimed adhesion. When cured, the elastomer resists weathering, ozone,
moisture, UV and high temperatures. SS-30 is also designed for superior oil
resistance.
Product Features
• Fast R.T. cure
• Thixotropic paste
• Excellent unprimed adhesion to plastic, metal and glass
• Very fast onset of adhesion
• Exceptional oil resistance
• Good hydrolytic stability
• Able to bond through oil
• Non-corrosive oxime cure
• Temperature range -65 to 260C
Colors: Black, blue, red, gray, copper
(custom colors available upon request)
Typical Applications
• Aftermarket adhesive sealant
• Automotive form in place gaskets
• Situations where the gasket flange is contaminated with oil
• Pressure can dispensing RTV
Service temperature
-65 to 260C
High Performance Automotive Silicone RTV Gasket Maker
Typical Properties
UNCURED
Viscosity, cps 400,000
Specific Gravity 1.28
Consistency : thixotropic paste
Working time, mins. @ R.T.: 8
Tack Free Time, mins. @ R.T.: 14
Application Rate, 90 PSI, g/min. >1000
3mm orifice @ 0.6 MPa
CURED - R.T.
Cured -24 Hrs. @ R.T.
Tensile Strength, PSI 275
Elongation, % 350
Durometer, Shore A 38
Peel Strength, PPI 20
Oil resistance - 5W30, 14 days 150C
Durometer 33 (12.1%)
Tensile 215 (22.0%)
Elongation 428 22.5%
Method of Application
Dispense sealant onto part. Mate parts, ensuring not all of the product is
squeezed out of flange assembly. Allow to cure.
Chemical cure system
Oxime cure system
Solids
98% solids, contains no solvents
Curing
Typical utilization involves dispensing in open air and ambient humidity to
result in a high strength adhesive rubber.
Cure speed can be accelerated with increased humidity to very rapid cures
exhibiting surprisingly fast adhesion.
Adhesion
Primerless adhesion to most plastics, metals and typical substrates.
Limitations
Do not use product on head gaskets or fuel immersion applications. Allow to
fully cure before putting assembly into service. Ensure enough product remains
between flanges to be effective in an assembly.
Packaging
SS-30 is available in 10.3 oz. cartridges,
50 lb. pails and 500 lb. drums. This product is also available in customer
defined packaging sizes, upon request.
Handling and safety
For maximum shelf life, keep containers sealed when not in use. Keep out of
the reach of children. Uncured sealant irritates eyes and skin. Refer to MSDS.
Shelf-life
Sealed containers are guaranteed for 1 year from the ship date when stored
in a cool dry area below 70 F.
Applicable standards and O.E.M. part number interchange
• Chrysler - 4206070, 4318025
• Ford - D6AZ-19562-B, E8AZ-19562-A, WSE-M46320-A2
• G.M. - 9985675, 1052751, 1052917, 12345739
Limited warranty
All recommendations, statements and technical data herein are based on tests
we believe to be reliable and correct, but accuracy and completeness of said
tests are not guaranteed and are not to be construed as warranty, either expressed
or applied. User shall rely on his own information and tests to determine
suitability of the product for the intended use, and the user assumes all
risk and liability resulting from the use of this product. Manufacturer’s
sole responsibility shall be to replace that portion of product of the manufacturer
proves to be defective. Manufacturer shall not be liable to the buyer or any
third party for injury, loss or damage directly or indirectly resulting from
the use of, or inability to use, the product.
Recommendations or statements other than those contained in a written agreement
signed by an officer of the manufacturer shall not be binding by the manufacturer.
This product has not been tested for, and is therefore not recommended for,
uses for which prolonged contact with mucous membranes, abraded skin, or blood
is intended; or for uses which implantation within the human body is intended.
** Customized versions available upon request **